The high-temperature strength has sharply declined. How should we select the product RH3400?

Hits: 585 img

One cannot simply rely on the fact that product RH3400 has a temperature resistance of 300-400°C or a tensile shear strength greater than 7 MPa at 200°C to directly conclude that it is suitable for all metal, ceramic or composite material bonding systems. Product RH3400 is a gray-black, three-component, silicone resin-modified cyanoacrylate adhesive without solvent, with a viscosity of approximately 3500 cp. One should first confirm the type of substrate and surface treatment, the three-component measurement and mixing sequence, the 40-minute operation time and application assembly cycle, the curing path selection (at room temperature for 5-7 days or at 130°C for 3 hours), the thickness of the adhesive layer, the operating temperature and atmosphere, thermal cycling and structural loading, before determining whether the problem is due to poor interface wetting, deviation in three-component ratio, uneven mixing, insufficient curing, thermal mismatch, high-temperature aging, or poor compatibility with the substrate and working conditions. Product RH3400 can be considered as a candidate for medium-high temperature structural bonding, but the tensile shear strength at 300°C is only greater than 1 MPa. The high-temperature load must be verified according to the actual temperature nodes, duration and safety factor.


1. Why does the strength of silicone resin-modified cyanoacrylate adhesives often drop sharply in high-temperature structural bonding?


The substrate surface is not cleaned or has oil stains, release agents, oxide layers, or dust, which affects the wetting and interface bonding of the adhesive to metals, ceramics or composite materials.


The three-component is not accurately measured according to the effective TDS ratio, or the mixing sequence, stirring method is improper, resulting in incomplete local curing, insufficient crosslinking density or inconsistent high-temperature performance.


The operation time is only 40 minutes, the mixing ratio is too large or the application assembly cycle is too slow, the adhesive material has thickened before coating or sealing, affecting wetting and final strength.


The curing path selection is inappropriate: a 5-7 day period at room temperature is too long if the environmental temperature is low or the time is insufficient, resulting in incomplete curing; heating at 130°C for 3 hours may cause internal stress or damage to the substrate if the temperature increase is too fast or the substrate's temperature resistance is insufficient.


The thickness of the adhesive layer is not controlled properly; too thick leads to increased curing shrinkage and thermal mismatch, too thin results in insufficient filling or discontinuous bonding.


When the operating temperature reaches around 300°C, the high-temperature load capacity of the resin matrix significantly decreases. The 300°C tensile shear strength given in the data is only greater than 1 MPa, which is significantly different from the 8 MPa at room temperature and 7 MPa at 200°C.


The high-temperature atmosphere control is improper, such as aging of the adhesive layer in an oxidative atmosphere, resulting in strength attenuation above 200°C.


Switching from epoxy adhesives, polyurethane adhesives, organic silicon adhesives, phosphates, borosiliconazanes or other cyanoacrylate adhesives, without re-adjusting the surface treatment, three-component ratio, adhesive layer thickness and curing curve, leads to strength deviation from the target.


Structures subjected to impact, vibration, shear or peel composite stress are selected based solely on tensile shear strength data, without verifying the actual loading form.


The product is a solvent-free three-component system, and bubbles have not been expelled after mixing, and the internal pores of the adhesive layer become stress concentration points.


Storage conditions do not meet the requirements of cool and dryness or exceed the 1-year shelf life, resulting in a decrease in the activity of the three components and fluctuations in curing quality and high-temperature strength.


Insufficient understanding of the 300-400°C temperature resistance range, failure to distinguish between short-term exposure and long-term bearing, and also failure to assess the safety factor after the strength drop above 300°C.


2. Determine which stage the problem of structural bonding or high-temperature strength occurs


Failure stage Possible causes Preferred inspection direction
The adhesive layer is not wetted or has local lack of adhesive after coating Unclean substrate, high viscosity of the adhesive, improper coating amount Substrate cleaning, adhesive viscosity, coating amount
The adhesive material thickens after three-component mixing or has insufficient shelf life Deviation in ratio, improper mixing sequence, excessive mixing ratio Three-component measurement, mixing sequence, 40-minute operation time
The strength is insufficient after 5-7 days of room temperature curing. Low environmental temperature, insufficient curing time, and deviation in the ratio. Environmental temperature, curing time, and the ratio of the three groups.
After 3 hours of curing at 130℃, cracking or high internal stress occurs. Rapid heating, thick adhesive layer, and mismatch in the thermal expansion of the substrate. Heating rate, adhesive layer thickness, and substrate treatment.
The tensile and shear strength does not meet the standard at room temperature or at 200℃. Incomplete curing, interface contamination, and adhesive layer defects. Curing quality, surface treatment, and adhesive layer uniformity.
The tensile and shear strength at 300℃ is lower than 1 MPa or insufficient bearing capacity. The strength of the high-temperature base material decreases due to oxidation and micro-crack expansion. Operating temperature, atmosphere, and bearing design.
The adhesive fails after impact or vibration. Excessive adhesive layer modulus, concentrated internal stress, and improper structural design. Adhesive layer thickness, structural stress, and impact test.
The strength or curing behavior varies between batches. Batch differences in the three-component mixture, or unstable ratio or coating. Incoming inspection, ratio records, and curing curve records.
If only focusing on "whether the product RH3400 was used", without recording substrate treatment, the ratio of the three groups, mixing sequence, operation time, curing path, operating temperature, and structural stress, it is usually difficult to accurately determine whether it is a material problem or a process problem.


Why extending the room temperature curing time or increasing the heating curing temperature may not be effective?


Product RH3400 plays a structural bearing role in the bonding system. It is affected by the substrate, the ratio of the three groups, the uniformity of the mixture, the thickness of the adhesive layer, the curing path, the operating temperature, and the structural stress. Simply extending the time or increasing the temperature may bring side effects.


Extending the room temperature curing time for more than 5-7 days may improve the curing degree, but it reduces production efficiency and is ineffective for contaminated or ratio-deviated adhesive materials.


Increasing the heating curing temperature may accelerate curing, but exceeding 130℃ or rapid heating may cause concentrated internal stress, adhesive layer cracking, or substrate damage.


Increasing the adhesive layer thickness may improve the filling capacity, but too thick will increase curing shrinkage and thermal mismatch, reducing the tensile strength.


Reducing the adhesive layer thickness may lower the internal stress, but it may result in insufficient adhesive, pores, or discontinuous bonding.


When the substrate surface is not cleaned, adjusting the curing time or temperature alone cannot solve the interface wetting and bonding problems.


If the ratio of the three groups is deviated or the mixing is not uniform, adjusting the curing curve alone cannot restore the crosslink density and high-temperature strength.


If the operation time is not completed within 40 minutes after applying the adhesive assembly, adjusting the curing conditions alone after the adhesive thickens cannot restore the wetting property.


If the strength drops sharply at 300℃ or above due to the upper limit of the resin base material's temperature, extending the curing time or increasing the temperature alone cannot fundamentally restore the high-temperature bearing capacity.


If the adhesive is expired or its activity has decreased, adjusting the process alone cannot restore the original performance.


Therefore, when optimizing, one should observe the substrate treatment, the ratio of the three groups, the mixing sequence, the operation time, the adhesive layer thickness, the curing path, the operating temperature, and the structural stress, rather than only adjusting a single parameter.


What are the differences in the selection of product RH3400 and product RH3400C and similar structural bonding schemes?


Comparison direction Product RH3400 (silicone modified epoxy acrylate type) Product RH3400C (modified epoxy acrylate type) Epoxy structural adhesive Polyurethane structural adhesive Organic silicone adhesive Boron-silicon-nitrogen/ polycarbon-silane adhesive
Temperature range Marked as 300-400℃ Marked as 300-400℃ Usually 150-200℃ Usually 100-150℃ Usually 200-400℃ Up to 1000-1500℃ or above
Number of components Three-component Three-component Two-component or single-component Two-component Single-component or two-component Single-component or two-component
Appearance Grey black Grey black Depending on the product Depending on the product Depending on the product Gray or grey black
Viscosity: Approximately 3500 cp, approximately 3500 cp, varies by product, varies by product, varies by product, 1000 - 4000 cp
Curing conditions: Room temperature for 5 - 7 days or 130°C for 3 hours, room temperature or heating, room temperature or heating, room temperature or heating, room temperature or heating, 170 - 220°C for 2 hours
Room temperature shear strength: greater than 8 MPa, greater than 9 MPa, relatively high, medium, average, greater than 5 - 10 MPa
200°C shear strength: greater than 7 MPa, greater than 9 MPa, significant decrease, significant decrease, decrease, 800°C compression shear greater than 8 MPa
300°C shear strength: greater than 1 MPa, not labeled, not applicable, not applicable, need verification, 1000°C compression shear greater than 8 MPa
Resin tensile strength: not labeled, greater than 50 MPa, varies by formula, varies by formula, average, varies by formula
Resin impact strength: not labeled, greater than 15 kJ/m², relatively brittle, better, better, slightly brittle
Operation time: 40 minutes, 40 minutes, varies by product, varies by product, varies by product, varies by product
Solvent-free: Yes, Yes, varies by product, varies by product, varies by product, Yes
Five, what parameters should be confirmed when using product RH3400?


Parameter category: Information to be confirmed
Application direction: Metal bonding, ceramic bonding, composite material bonding
Base material type: Metal, ceramic, composite material and surface condition
Surface treatment: Cleaning method, degreasing, removal of oxide layer, drying degree
Three-component mixing ratio: Confirm the ratio according to the effective TDS, measure the accuracy of each component
Mixing sequence: Order of adding the three components, mixing method, mixing time
Operation time: 40 minutes, match the compatibility of the glue dosage and assembly cycle
Coating process: Coating amount, layer thickness, uniformity, whether to remove air bubbles
Curing path: Room temperature for 5 - 7 days or 130°C for 3 hours, environmental temperature and heating rate
Usage temperature: Long-term temperature, peak temperature, 200°C and 300°C loading conditions
Usage atmosphere: Air, inert gas, oxidizing or reducing atmosphere
Thermal cycling: Heating and cooling rate, number of cycles, high and low temperature holding time
Structural stress: Shear, impact, vibration, peel and composite stress
Storage conditions: Cool and dry place, sealed, shelf life 1 year
Acceptance indicators: Room temperature shear strength, 200°C shear strength, 300°C shear strength, strength retention rate after thermal cycling, integrity after impact and vibration
Six, what should be mainly verified when using product RH3400?


Three-component mixing accuracy, mixing sequence and mixing uniformity.


The feasibility of glue assembly within 40 minutes and the fluidity of the adhesive.


The wetting property of the base material surface treatment and the continuity of the adhesive layer.


Room temperature shear strength after 5 - 7 days of curing.


Shear strength after 130°C × 3 hours of curing, internal stress and appearance.


Whether the room temperature shear strength is greater than 8 MPa, whether the 200°C shear strength is greater than 7 MPa.


Whether the 300°C shear strength is greater than 1 MPa and evaluate the safety factor for 300 - 400°C loading.


The influence of adhesive layer thickness on shear strength and thermal mismatch.


The strength retention rate and interface integrity after 300 - 400°C long-term use.


The reliability of adhesion after thermal cycling, impact and vibration.


The consistency of different base materials and surface treatments.


The consistency of three-component state, curing behavior and strength between batches.


The changes in three-component activity and curing performance within 1 year of storage.


The effectiveness of ventilation environment and operator protection.


Seven, how to design experiments before using product RH3400?


Establish a benchmark for the current structural adhesive, record the model, surface treatment, ratio, mixing sequence, layer thickness, curing path and failure performance.
Unified test conditions: substrate, surface treatment, three-component mixing ratios, mixing sequence, adhesive layer thickness, curing path, operating temperature, atmosphere and thermal cycling conditions.


Setting candidate samples: current structural adhesive, product RH3400, product RH3400C, different adhesive layer thickness or curing path gradients.


Completing the entire process of testing: surface treatment → three-component metering → mixing in sequence → applying adhesive → curing → room temperature pull-off test → 200℃ pull-off test → 300℃ pull-off test → aging at 300-400℃ → thermal cycling → impact vibration test.


Evaluating actual results: room temperature strength, 200℃ strength, 300℃ strength, strength retention rate after thermal cycling, integrity after impact vibration.


Test items Unified requirements
Substrate and surface treatment Keep consistent or set gradients according to the test design
Three-component mixing ratios Confirmed and kept consistent according to the effective TDS
Mixing sequence and method Set gradients according to the test design
Operation time Controlled within 40 minutes, record the amount of adhesive and application rhythm
Adhesive layer thickness Set gradients according to the test design
Curing path 5-7 days at room temperature or 130℃ × 3 hours, set according to the test design
Operating temperature Set according to room temperature, 200℃, 300℃, 300-400℃ nodes
Operating atmosphere Set according to actual working conditions
Thermal cycling and impact vibration Set the number of cycles and force application form according to actual working conditions
Measurement method Consistent strength retention rate after thermal cycling
Eight. Which situations are not suitable for directly using product RH3400?


If the substrate surface is not cleaned or there is oil stains, oxide layer, or release agent, it will affect the interface bonding.


The three-component mixing ratios cannot be accurately controlled according to the effective TDS, or the mixing sequence and stirring are not uniform.


The amount of adhesive is too large or the application assembly rhythm cannot be completed within 40 minutes of operation time.


The curing environment at room temperature is too low or the time is insufficient, or the 130℃ heating curing condition is not available.


The operating temperature exceeds 300℃ and the load is high, and the safety factor has not been evaluated based on the data of 300℃ pull-off test greater than 1 MPa.


The operating atmosphere is strong oxidation, and the antioxidant ability of the adhesive layer and substrate has not been verified.


The structure is subjected to strong impact, vibration or peel stress, and the actual force application form has not been verified.


Specific food contact, medical or airworthiness approval is required, but the corresponding data has not been obtained.


Only the operating temperature is known, and the substrate, three-component mixing ratios, mixing sequence, adhesive layer thickness, curing path and operating atmosphere data are not available.


The customer requests to directly mix it into the in-use system, but the surface treatment, mixing ratio, mixing, coating and curing conditions cannot be controlled.


When switching from epoxy, polyurethane, organic silicon, borosilicon nitride, polycarbon silane or other acrylate-based adhesives, the process should not be re-adjusted.


Storage conditions do not meet the requirements of cool and dry, sealed, or exceed the 1-year shelf life.


Poor ventilation in the operation environment affects the health of the operators.


The strength retention rate after 300-400℃ long-term bearing and thermal cycling has not been evaluated.


Ten. What selection support can our company provide?


As a solution provider for the entire organic silicon chain, our company can assist in comparing the applicability of silicone resin modified acrylate-based adhesives in different substrates, three-component mixing ratios, mixing sequences, adhesive layer thickness, curing paths and high-temperature conditions based on product RH3400.


For projects that need to consider the bonding of metal, ceramic or composite materials, as well as room temperature, 200℃ and 300℃ pull-off strength, impact toughness and 300-400℃ temperature resistance, before selection, the following should be provided:


Application direction and substrate type.


Target room temperature pull-off strength, 200℃ pull-off strength and 300℃ load requirements.


Surface treatment method and structural stress form.


Three-component mixing ratios, mixing sequence and operation time requirements.


Layer thickness and coating process.


Selection of curing path (at room temperature for 5-7 days or at 130°C for 3 hours) and environmental conditions.


Operating temperature, atmosphere and thermal cycling requirements.


Impact, vibration and peel stress requirements.


Current adhesive model, process and failure performance.


Acceptance method and applicable standards.


After receiving complete materials, it can be determined whether to test a certain ratio, mixing and curing scheme of product RH3400, or to choose product RH3400C, epoxy, polyurethane, silicone or other high-temperature resistant structural adhesives.


X. Common Misconceptions


It is possible to use at full load above 300°C for a long time with a temperature resistance of 300-400°C.
The data shows that the tensile shear strength at 300°C is only greater than 1 MPa, which is significantly lower than 8 MPa at room temperature and 7 MPa at 200°C. 30

Online QQ Service, Click here

QQ Service

What's App