How to select the product H11500 for high-temperature bonding?
Hits: 587
img
One cannot simply rely on the data of product H11500's resistance to temperatures ranging from 1300 to 1500°C, or its shear strength at a certain temperature, to directly determine that it is suitable for all bonding and sealing systems involving graphite, metals, ceramics, or composites. Product H11500 is a gray, single-component, solvent-free borosilicon-nitrogen-based adhesive with a viscosity of 3000 to 4000 cp. The curing conditions are: heating in the furnace to 170°C, curing for 2 hours, and then cooling in the furnace. One should first confirm the type of substrate, surface treatment, layer thickness, curing temperature curve, operating temperature and atmosphere, thermal cycling conditions, sealing structure, and ventilation conditions, before determining whether the problem is due to poor interface wetting, incomplete curing, thermal expansion mismatch, high-temperature oxidation, or adhesive layer defects, or due to poor compatibility with the substrate and working conditions. Product H11500 can be considered as a candidate for ultra-high temperature bonding and sealing, but it must be verified through small-scale tests, bonding strength tests, and actual high-temperature working conditions.
1. Why does the strength of borosilicon-nitrogen-based adhesives often decrease in high-temperature bonding or sealing?
The surface of the substrate is not cleaned or is contaminated with oil, release agents, oxide layers, or dust, which affects the wetting of the adhesive by the graphite, metal, or ceramic and the interface bonding.
The graphite material has a high porosity, and when the viscosity and coating amount of the adhesive do not match, the adhesive layer may over-penetrate or be locally deficient, forming a weak interface.
The curing temperature curve does not match the product requirements. If the curing is not carried out as per the instructions of heating in the furnace to 170°C, curing for 2 hours, and then cooling in the furnace, it may result in incomplete curing or the generation of internal stress.
The thickness of the adhesive layer is not controlled properly. If it is too thick, the shrinkage and thermal mismatch at high temperatures increase, and if it is too thin, it may not be adequately filled. Both cases will reduce the shear strength.
Using temperatures beyond the long-term tolerance range of the materials or undergoing high-temperature cycling repeatedly causes the adhesive layer to develop microcracks and gradually expand.
The improper control of the high-temperature atmosphere, such as in an oxidative atmosphere where the graphite or adhesive layer oxidizes, leads to a decrease in interface strength.
The product is a single-component borosilicon-nitrogen-based adhesive. If left for a long time or opened, ammonia gas may escape, and poor ventilation can affect the operating environment and may mask changes in the adhesive material state.
Switching from phosphate-based adhesives, organic silicone adhesives, phenolic resins, or other high-temperature-resistant adhesives without adjusting the surface treatment, adhesive layer thickness, and curing curve leads to deviations in strength from the target.
The thermal expansion coefficients of metals, ceramics, or composites differ significantly from that of graphite. The transition layer or structural design is not used to buffer thermal stress.
The adhesive layer in the sealing structure is subjected to pressure, shear, and thermal cycling, and only a single shear strength data is used for selection, without verifying the actual sealing conditions.
Storage conditions do not meet the requirements of a cool and dry environment or exceed the shelf life of 1 year, resulting in a decrease in adhesive material activity and fluctuations in curing quality and high-temperature strength.
The understanding of typical data of 1500°C shear strength greater than 2 MPa is insufficient. The strength already decreases at high temperatures, and it is not designed based on actual load and safety factors.
2. Determine at which stage the problem of high-temperature bonding or sealing occurs
Failure stage Possible causes Preferred inspection direction
The adhesive layer does not wet or is locally deficient after coating Unclean substrate, porosity of graphite, high adhesive viscosity Surface treatment, adhesive viscosity, coating amount
Insufficient room-temperature strength after curing Deviation of curing curve, thick adhesive layer, interface contamination Heating curve, adhesive layer thickness, substrate treatment
Lower than expected shear strength at 400-1000°C Incomplete curing, thermal mismatch, adhesive layer defect Adhesive curing quality, thermal expansion matching, adhesive layer uniformity
The shear strength rapidly decreases at 1500°C High-temperature ceramicization shrinkage, oxidation, microcrack expansion Using atmosphere, thermal cycling, structural design
The adhesive layer cracks or detaches after thermal cycling Thermal expansion coefficient difference, thick adhesive layer, rapid heating Thermal expansion matching, adhesive layer thickness, heating and cooling rate
Leakage of the sealing structure Discontinuous rubber layer, pores, interface detachment Coating process, curing curve, sealing structure
Strong ammonia smell or thickened rubber material after opening the cover Improper storage conditions, long-term storage, poor sealing Storage temperature, container sealing, shelf life
Fluctuations in strength between batches Batch differences in rubber material, coating or curing records Incoming inspection, coating records, curing curve records
If only focusing on "whether product H11500 was used", but without recording substrate treatment, rubber layer thickness, curing curve, usage atmosphere and thermal cycling conditions, it is usually difficult to accurately determine whether it is a material problem or a process problem.
III. Why increasing the curing temperature or increasing the rubber layer thickness may not be effective?
Increasing the curing temperature may accelerate curing, but exceeding the recommended curve may cause increased rubber layer shrinkage, internal stress concentration or substrate damage.
Extending the curing time may improve the curing degree, but it may affect production efficiency and is ineffective for contaminated or expired rubber materials.
Increasing the rubber layer thickness may improve filling capacity, but too thick will increase high-temperature shrinkage and thermal mismatch, reducing shear strength at low temperatures.
Reducing the rubber layer thickness may reduce thermal stress, but it may lead to missing glue, pores or discontinuous sealing.
When the substrate surface is not cleaned, only adjusting the curing temperature or rubber layer thickness cannot solve the problems of interface wetting and bonding.
When the graphite porosity is high, increasing the rubber quantity may cause excessive penetration of the rubber material, insufficient surface rubber layer.
When micro cracks occur due to high-temperature oxidation or thermal cycling, only increasing the curing temperature cannot restore strength.
When the rubber material state changes after expired storage or ammonia overflow, only adjusting the process cannot restore the original performance.
Therefore, when optimizing, one should observe substrate treatment, rubber viscosity, rubber layer thickness, curing curve, usage atmosphere and thermal cycling conditions, rather than only adjusting a single parameter.
IV. What public parameters and applicable directions does product H11500 have?
Parameter category Open information
Appearance Grey
Number of components Single component
Solvent No solvent
Chemical type Phosphorus-containing silane nitrogen-based adhesive
Viscosity 3000-4000 cp
Curing conditions Heating in furnace to 170°C, curing for 2 hours, cooling in furnace
Room temperature bonding strength of graphite More than 5 MPa
400°C shear strength More than 8 MPa
800°C shear strength More than 8 MPa
1000°C shear strength More than 8 MPa
1500°C shear strength More than 2 MPa
Storage period Dark and dry, with a shelf life of 1 year
Applicable directions should be listed point by point:
High-temperature bonding of graphite materials. Suitable for bonding and repairing graphite electrodes, graphite crucibles, graphite heating elements, graphite molds, etc., and verification of room temperature and 400-1500°C shear strength is required.
Bonding of metals and ceramics. Can be used for high-temperature bonding of metal and ceramic components, and the thermal expansion matching and interface bonding need to be evaluated.
Bonding of composite materials. Can be used for connection and repair of ceramic-based and carbon-based composite materials, and verification should be conducted according to the actual material system.
High-temperature sealing. Suitable for sealing of high-temperature equipment, pipelines, furnace bodies, etc., and verification of pressure, thermal cycling and leakage rate is required.
Preparation of high-temperature coatings. Can be used as the basic component of high-temperature coating materials, and the coating adhesion, thickness and thermal shock resistance need to be verified.
The above data are typical parameters of the product, not as factory standards. Formal procurement and batch acceptance should be based on the effective TDS, specification sheet and delivery batch COA confirmed by both parties.
V. What parameters should be confirmed when using product H11500?
Parameter category Information to be confirmed
Application direction High-temperature bonding of graphite, metal bonding, ceramic bonding, composite material bonding, high-temperature sealing, high-temperature coating
Substrate type Graphite, metal, ceramic, composite material and surface condition
Surface treatment: Cleaning method, degreasing, removal of oxide layer, drying degree, graphite pore treatment
Material state: Gray color, viscosity 3000-4000 cp, whether placed for a long time, ammonia gas situation after opening the cover
Coating process: Coating amount, coating layer thickness, uniformity, whether multiple coatings are required
Curing curve: Furnace heating to 170℃, holding for 2 hours, furnace cooling
Operating temperature: Long-term temperature, peak temperature, 1500℃ short-term exposure condition
Operating atmosphere: Air, inert gas, vacuum, oxidation or reduction atmosphere
Thermal cycling: Heating and cooling rate, number of cycles, high and low temperature holding time
Sealing structure: Gap, pressure, loading method, leakage requirements
Storage conditions: Cool and dry place, sealed, shelf life 1 year
Acceptance indicators: Room temperature bonding strength, 400/800/1000/1500℃ shear strength, sealing performance, strength retention rate after thermal cycling
Six. What should be mainly verified when using product H11500?
Wetting property of the substrate surface after surface treatment and continuity of the coating layer.
Whether the curing curve is executed according to 170℃×2 hours, and whether the furnace cooling is sufficient.
Whether the room temperature bonding strength is greater than 5 MPa.
Whether the 400℃, 800℃, 1000℃ shear strength is greater than 8 MPa.
Whether the 1500℃ shear strength is greater than 2 MPa and the safety factor is evaluated.
The influence of coating layer thickness on shear strength and thermal mismatch.
The strength retention rate and interface integrity after thermal cycling.
The impact of operating atmosphere on the oxidation of the coating layer, graphite oxidation and sealing performance.
The consistency of bonding between graphite, metal, ceramic, and composite materials.
The leakage rate and pressure holding capacity of the sealing structure.
The influence of ammonia gas emission and ventilation conditions on the operation when opening the cover.
The consistency of coating viscosity, curing behavior and high-temperature strength among batches.
Seven. How to design experiments before using product H11500?
Establish a benchmark for the current high-temperature adhesive, record the model, surface treatment, coating layer thickness, curing curve and failure performance.
Uniform test conditions: substrate, surface treatment, coating layer thickness, curing curve, operating temperature, atmosphere and thermal cycling conditions.
Set candidate samples: current adhesive, product H11500, different coating layer thickness or curing curve gradients.
Complete the full process testing: surface treatment → coating → curing → room temperature strength → high-temperature shear strength → thermal cycling → sealing performance test.
Evaluate actual results: room temperature strength, shear strength at various temperatures, strength retention rate after thermal cycling, sealing performance.
Test items Uniform requirements
Substrate and surface treatment Keep consistent or set gradients according to the test design
Coating layer thickness Set gradients according to the test design
Curing curve Set gradients according to the 170℃×2h benchmark
Operating temperature Set according to 400/800/1000/1500℃
Operating atmosphere Set according to actual working conditions
Thermal cycling conditions Set according to actual heating and cooling rates and cycle times
Measurement method Uniform room temperature strength, shear strength, sealing performance, strength retention rate after thermal cycling
Eight. Under which circumstances should product H11500 not be directly used?
The substrate surface is not cleaned or has oil stains, oxide layer, or release agent, which affects the interface bonding.
The graphite porosity has not been evaluated, and the coating viscosity and coating amount cannot be matched.
The curing curve cannot be executed according to 170℃×2 hours or the furnace cooling conditions are not available.
The operating temperature exceeds 1300-1500℃ for a long time, and the high-temperature creep and oxidation have not been evaluated.
The operating atmosphere is highly oxidizing, and the antioxidant capacity of the coating layer and substrate has not been verified.
The sealing structure can withstand high pressure or strong vibration, and the actual sealing working condition verification has not been conducted.
Specific food contact, medical or airworthiness approval is required, but corresponding materials have not been obtained.
Only the temperature usage is mastered, without the substrate, the thickness of the adhesive layer, the curing curve and the atmosphere data.
The customer requests to directly mix it into the existing system, but cannot control the surface treatment, coating and curing conditions.
When switching from phosphate, organic silicon or other high-temperature resistant adhesives, the process has not been re-adjusted.
The storage conditions do not meet the requirements of cool and dry, sealed, or exceed the shelf life of 1 year.
The operation environment has poor ventilation, and ammonia gas overflow from the lid affects the health of the operators.
The safety factor and load design for the 1500℃ shear strength greater than 2MPa have not been evaluated.
IX. Common Misconceptions
It is believed that a material with a temperature resistance of 1300-1500℃ can be used for long-term full-load operation at 1500℃: The data shows that the shear strength at 1500℃ is greater than 2MPa, and the strength decreases at high temperatures, so it needs to be evaluated based on actual load, safety factor and time, and cannot be judged solely based on the upper limit of temperature resistance.
The higher the curing temperature, the higher the strength: The curing should be carried out according to 170℃×2 hours and furnace cooling, and exceeding the recommended curve may lead to shrinkage, internal stress and damage to the substrate.
The thicker the adhesive layer, the stronger the bonding: An overly thick adhesive layer will increase the high-temperature shrinkage and thermal mismatch, reducing the shear strength, and the thickness should be optimized according to the substrate and structure.
The roughness of the graphite surface does not necessarily mean a strong bond: The porosity and surface contamination of the graphite will affect the penetration of the adhesive and the interface bonding, and it is necessary to clean and evaluate the coating amount.
Adhesion can be directly applied to the substrate: It is still necessary to confirm the surface treatment, adhesive layer thickness, curing curve, usage atmosphere and thermal cycling conditions.
The same strength at 25℃ can be replaced quantitatively: Different high-temperature adhesives have different high-temperature strengths, thermal mismatch and curing behaviors, and replacement requires re-verification.
Product H11500 can be used for all high-temperature bonding and sealing: This product is suitable for bonding and sealing of graphite, metal, ceramic and composite materials, as well as high-temperature coatings. For systems with strong oxidation, high-pressure sealing or special industry approval requirements, it needs to be specifically verified.
The ammonia smell can be ignored: The product may have ammonia overflow when opened or left for a long time, and it should be used in a ventilated environment and protected.
X. Recommended Selection Steps
Confirm the application direction: Graphite bonding, metal/ceramic/composite material bonding, sealing or high-temperature coating.
Confirm the substrate type, surface treatment and graphite porosity.
Confirm the adhesive state, viscosity and storage period.
Confirm the thickness of the adhesive layer and coating process.
Confirm the curing curve as furnace heating to 170℃, curing for 2 hours, and furnace cooling.
Confirm the usage temperature, atmosphere and thermal cycling conditions.
Select product H11500 or other high-temperature adhesives based on the application scenario.
Carry out small tests with different adhesive layer thicknesses and curing curve gradients.
Test the shear strength at room temperature and 400/800/1000/1500℃.
Perform thermal cycling, atmosphere and sealingity verification.
Evaluate the consistency of adhesive state and high-temperature strength between batches.
Confirm that the ventilation, moisture-proof and storage conditions are in place.
After completing multiple batch and actual working condition verification, determine the final usage plan.
Our company, as a provider of the entire organic silicon industry chain, can assist in comparing the applicability of borosilicon nitrogen-based adhesives in different substrates, adhesive layer thickness, curing curves and high-temperature conditions. For graphite, metal, ceramic or composite material bonding and sealing projects, before selection, provide the application direction, substrate type, target room temperature and shear strength at 400-1500℃, surface treatment method, adhesive layer thickness, curing curve, usage atmosphere and thermal cycling requirements, and then determine whether to prioritize testing a certain coating and curing scheme of product H11500 or choose the route of other high-temperature adhesives.